How to Prevent Automatic Driver Installation on Windows 10

How to Prevent Automatic Driver Installation on Windows 10
Posted by Admin
Your Ads Here

Windows 10 is an operating system that has been greatly upgraded in terms of security compared to previous versions, one of which is the ability to block unknown drivers from being installed on Windows 10. However, for one For advanced users, this feature is quite inconvenient. Taimienphi will guide you how to turn off the feature to prevent installation of unknown drivers on Windows 10.

Windows 10 is increasingly improving its security capabilities after important updates. One of them is the ability to block unknown drivers (drivers). Usually, drivers will be released by manufacturers with their devices, censored, authenticated and signed by Microsoft, these drivers will be installed on devices running Windows. to make sure your computer is controlled by "original" drivers and is safe.

What if we mistakenly installed a malicious driver on the computer. Not just normal software, drivers also affect the top layer of the system (kernel). If a malicious driver is installed on the computer, the impact is not only on the software on the computer but also on the computer system.

However, for programmers or advanced users, drivers that they have tweaked or tested themselves will not work on Windows 10. So how to deal with this problem? Taimienphi will guide you to turn off the feature to prevent unknown drivers on Windows 10. Please note, this guide should only be manipulated when you really understand the system as well as the driver that is about to be installed.


Turn off Blocking Installing Unknown Drivers Through Recovery

Note: This method is only applicable to Windows 10 versions older than Anniversary Update (ver 1607)

Step 1: Press Windows + I , click Update & Security

Step 2: Select Recovery, click Advance startup

Step 3: The computer will restart in Advance Startup mode, click Troubleshoot

Step 4: Select Advanced Options

Step 5: Select Startup Settings

Step 6: Click Restart to restart the computer and select the boot method

Step 7: Press F7 to enable Disable Driver Signature Enforcement

The computer is restarted, and from here you can install unregistered drivers.

Disable Secure Boot Mode

Secure Boot is a secure boot mode set up on the next generation BIOS with UEFI standard. With many improvements, this is considered one of the best security mechanisms for your system. For this reason, it is very difficult to install unknown drivers into the UEFI standard system.

Taimienphi will guide you to turn off Secure Boot, however, this is a method that will affect the security of the system, so you need to consider carefully before manipulation.

Step 1: The operation to start Advanced Startup mode is similar to method 1.

Step 2: Click Troubleshoot

Step 3: Click on Advanced Settings

Step 4: Click UEFI Firmware Setting

Step 5: Click Restart to reboot into Firmware UEFI installation mode

From here, different models will have different Firmware installation interfaces. You find the Secure Boot item to Disable.





After the operation is complete, you repeat the same steps as above to re-enable Secure Boot mode

Install Drivers Of Unknown Sources In Test Mode

Test Mode is a hidden mode in Windows 10 that allows advanced users and programmers to more easily manipulate the software they build when bypassing rigorous security checks on the system. Windows. Therefore, unknown drivers can be installed easily in this mode. You start this mode according to the instructions below

Step 1: Press the Windows + X key combination, click Windows Powershell (Admin) to start the Windows Powershell command program

Step 2: Type the command bcdedit /set testsigning on

Step 3: Here, if successful, you will restart the machine, your Windows 10 will be in Test Mode. If there is an error message, maybe the Secure Boot feature on your computer is turned on, please repeat the steps as above in the 2nd method to turn off Secure Boot.

Step 4: After completing the testing and testing of unknown drivers on Windows 10, reopen the Windows Powershell interface, turn off Test Mode with the command

bcdedit /set testsigning off

Above are some instructions on how to turn off the feature of blocking the installation of unknown drivers on Windows 10. If you are a general user, we recommend that you install the "original" drivers. " are provided by the device manufacturers themselves to ensure the security of your computer system or install the driver automatically via Driver Booster for the most stable operation of the devices.

Your Ads Here

Your Ads Here

Your Ads Here

Your Ads Here

Newer Posts Newer Posts Older Posts Older Posts

Related Posts

Your Ads Here


Post a Comment
Loading comments...